SB-6715 Sealer 5 Gallon-Kit (Part A and B) SB-6715 Sealer 5 Gallon-Kit (Part A and B) SB-6715 Sealer 5 Gallon-Kit (Part A and B) SB-6715 Sealer 5 Gallon-Kit (Part A and B)
SB-6715 Sealer 5 Gallon-Kit (Part A and B) SB-6715 Sealer 5 Gallon-Kit (Part A and B) SB-6715 Sealer 5 Gallon-Kit (Part A and B) SB-6715 Sealer 5 Gallon-Kit (Part A and B)

SB-6715 Sealer 5 Gallon-Kit (Part A and B)

$210.00

Two-Part Urethane Wet Look Joint Stabilizing Sealer

+ -
Add to Cart
Product Number: SB-6715
Availability: In Stock


Surebond 6715 - Two Part Urethane Wet Look Joint Stabilizing Sealer

Hardscapes done right!


SB-6715 SurfacePRO RTU is a proprietary two-part, clear, aliphatic urethane sealer and joint sand stabilizer. SB-6715 is specially formulated with an antifungal designed to help inhibit the growth of mold, moss and algae on the sealer film when applied to horizontal or vertical surfaces. SB-6715 is a multi-use product: it enhances with a semi-gloss finish, provides good surface protection and joint sand stabilization. This product can be used inside and outside on old and new surfaces. Optimal results when performing same day cleaning, sanding and sealing with SB-6715, can be achieved when following the recommended application process. SB-6715 provides a non-yellowing protective layer on the surface that is durable and resistant to mild acid, alkali, chemicals and salt attacks. SB-6715 will increase the stain resistance of the surface and allow easier cleaning, maintenance, and extended wear. On new concrete, mortar, grout or overlays, it is recommended to wait 7 days before applying SB-6715 to allow for curing. SB-6715 is a water-based two component product that requires mixing and should not be diluted. Once mixed, it has the consistency of water and is milky white when applied and dries clear. Cured sealer is freeze resistant to -60°F (-51°C) and is stable up to a temperature of 180°F (-51°C).

FEATURES:

  • Enhancement – Darkens Surface Tone
  • Good Joint Sand Stabilization – Reduces Sand Loss
  • Provides a Semi-Gloss Sheen
  • Good Durability and Long Term Performance
  • Antifungal Film Protection – Protects sealer film from growth of mold, moss and algae
  • Breathable – Does Not Trap Moisture or Efflorescence
  • Low VOC – Environmentally Friendly, Water Based Formula

SUITABLE SURFACES

Ideal for concrete and clay pavers, flat and stamped concrete, or natural and manufactured stone. Also suitable for masonry, retaining walls,porous or unglazed tile and terrazzo. Recommended for high traffic areas where high durability and superior chemical resistance is desired. NOT recommended for marble, granite, ceramic tile or porcelain.

A test area is always recommended to determine product suitability and compatibility with your specific surface before use and also if desired results are achievable. Due to the inherent variability of natural stone and clay products, long term performance may vary. Please consult with us prior to sealing if there are concerns.
Application Sq.Feet Sq.Meters
Sealing with joint stabilization 80 – 120 7.4 – 11.1
Sealing only without joint stabilization 200 – 300 18.6 – 27.9

Note: Single application. Actual coverage may vary depending on type, age, condition, joint size and porosity of the surface, application method and site conditions such as temperature. For more uniform coverage, a second coat must be applied after the first coat has dried to the touch.

0 stars based on 0 reviews

Add to Wishlist / Add to Compare

WARNING: This product can expose you to chemicals known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.